#OMB STL MTMR MANUAL MANUAL#
#OMB STL MTMR MANUAL SERIES#

When a military installation or Government - related facility(whether or not specifically named) is located partially within more than one city or county boundary, the applicable per diem rate for the entire installation or facility is the higher of the rates which apply to the cities and / or counties, even though part(s) of such activities may be located outside the defined per diem locality. Per diem localities with county definitions shall include 'all locations within, or entirely surrounded by, the corporate limits of the key city as well as the boundaries of the listed counties, including independent entities located within the boundaries of the key city and the listed counties (unless otherwise listed separately).'

#OMB STL MTMR MANUAL MANUAL#

Unless otherwise specified, the per diem locality is defined as 'all locations within, or entirely surrounded by, the corporate limits of the key city, including independent entities located within those boundaries.' with EPA guidelines contained in the Draft Manual for Infectious Waste Management.

When handwheel is used, thrust bearings are supplied as follows:ĪSME Classes 150–300: NPS 10–12 (DN 250–300), 1 bearing (top)ĪSME Classes 600–1500: NPS 6 (DN 150) and up.Traveler reimbursement is based on the location of the work activities and not the accommodations, unless lodging is not available at the work activity, then the agency may authorize the rate where lodging is obtained.

Rotating stem nut is Austenitic ductile iron Gr.

One-piece bonnet for better alignment and fewer parts for Class 150 up to NPS 16 (DN 400).

Body and bonnet castings are precision machined.

Body and bonnet joint accurately machined.

Non-rotating stem with precision Acme threads and burnished finish.

A CoCr alloy hardfaced CF8M wedge is also available.

Wedge is ground and lapped to a mirror finish and tightly guided to prevent dragging and seat damage.

Flexible wedge with low center stem-wedge contact, in solid CA15 (13Cr) or hardfaced with 13Cr, SS 316, Monel or CoCr alloy.

Seat face CoCr alloy hardfaced, ground and lapped to a mirror finish.

Universal trim: 13Cr stem, wedge in CA 15 or 13Cr faced, and CoCr alloy faced seat API Trim 8 suitable for applications up to 850☏ (454☌).

Bellows seal API 602 small forged valves.

Bellows seal cast steel valves (Bolted Bonnet).

Bellows seal bolted bonnet high pressure valves (large forged).

Type HPTD & VTS thermodynamic steam traps.

Type SPF & SP high capacity piston-operated steam traps.

Type Q250 hermetically-sealed steam traps.

Type MFT & MFTS float bimetallic steam traps.

Type MFA & MFAS compressed air drain traps.

RAMA easy maintenance valves for nuclear service.

Butt weld end type - PZ dual plate check valve.

Hub end type - PH dual plate check valve.

Double flanged type - PF, PG dual plate check valve.

Solid Lug type - PL, PM, dual plate check valves.

Wafer type - PW dual-plate check valves.

#OMB STL MTMR MANUAL SERIES#

XB series bonnetless globe valves (discontinued).

Bellows seal globe valves, hermetically-sealed y-pattern.

API 602 small forged HF acid globe valves.

API 602 HF acid small forged gate valves.

Cast stainless steel corrosion resistant valves.Bolted bonnet bellows seal globe valves.Bolted bonnet bellows seal flexible wedge gate valves.Bolted bonnet parallel slide gate valves.The manual MR process with a threshold amount of 3,700 was replaced by the. Bolted bonnet flexible wedge gate valves 100-04, Medicare Claims Processing Manual, Chapter 23 (available on the CMS.Bolted bonnet high pressure valves (large forged) valves.Pressure seal y-pattern piston check valves.Pressure seal tilting disc check valves.Pressure seal parallel slide gate valves.Pressure seal flexible wedge gate valves.Pressure seal (forged and cast steel) valves.The information collection requirements contained in this section have been approved by the Office of Management and Budget (OMB) and listed under OMB control number 1218-0150, as announced at Federal Register, Volume 54, No. Torqseal cryogenic triple offset valves Rotating stem nut is Austenitic ductile iron Gr. 147 have an effective date of January 2, 1990.Cap-Tight batch digester capping valves.Velflex high performance cryogenic butterfly valves.R-series cast and forged metal-seated ball valves.N-series forged metal-seated ball valves.

Type L high-temperature metal-seated ball valves.

Top-entry in-line repairable ball valves.

VTP-2000 high performance three-piece ball valves.

Omb stl mtmr manual